及時凈化油箱雜質，避免造成供油時間不準等現象；及時清除積炭，因為發電機工作時會(huì )讓有關部件溫度升高，容易導致灰炭聚合物附著在氣門等地方，應及時清理；保持水溫，發電機的冷卻水溫保持在45-65度左右；定期檢查，定期檢查調整氣門間隙、噴油壓力、供油時間等方面，能讓發電機處于良好的工作狀態。

Clean impurities in the oil tank in time to avoid inaccurate oil supply time; Timely remove the carbon deposits, because the temperature of relevant components will rise when the generator is working, which may easily cause the ash carbon polymer to adhere to the valve and other places, so it should be cleaned in time; Keep the water temperature, and the cooling water temperature of the generator is about 45-65 ℃; Regular inspection, regular inspection and adjustment of valve clearance, injection pressure, oil supply time, etc. can keep the generator in good working condition.

一、保持發電機凈化

1、 Keep generator clean

焦化發電機組油箱在使用一段時間后，箱底一般會(huì )沉淀一些礦物質或雜質，應定期清除或凈化。否則會(huì )對柱塞和噴油頭的正常運作帶來巨大影響，造成供油時間不準、供油不均勻、油料霧化不良等現象，致使增加油耗，功率下降。

After the oil tank of coking generator unit has been used for a period of time, some minerals or impurities will be deposited at the bottom of the tank, which should be removed or purified regularly. Otherwise, it will have a huge impact on the normal operation of the plunger and fuel injector, causing inaccurate fuel supply time, uneven fuel supply, poor fuel atomization and other phenomena, resulting in increased fuel consumption and reduced power.

二、積炭及時清除

2、 Timely remove carbon deposits

發電機在工作時，由于燃燒過程中，各有關部件溫度會(huì )升高，導致灰炭聚合物附著在氣門、氣門座、噴油嘴、活塞頂部等地方，如果不及時清理，會(huì )增加油耗，嚴重影響發動機的正常運作。所以積炭要及時清除，建議是半年清除一次。

During the operation of the generator, the temperature of all relevant components will rise during the combustion process, causing the ash carbon polymer to adhere to the valve, valve seat, fuel injection nozzle, piston top and other places. If it is not cleaned in time, it will increase the fuel consumption and seriously affect the normal operation of the engine. Therefore, the carbon deposit should be removed in a timely manner. It is recommended that it be removed once every six months.

一般情況下，建議是 4-6 個月清除一次。

In general, it is recommended to clean it once every 4-6 months.

三、保持水溫

3、 Maintain water temperature

焦化發電機組的發電機發動機的冷卻水溫保持在45-65度左右。若水溫過低，會(huì )造成發電機燃燒不完全，加大機器本身負荷量。冷卻水建議是用不含礦物質的“軟水”(如蒸餾水、雨水)，不宜濫用污水、渾水。

The cooling water temperature of the generator engine of the coking generator set is about 45-65 ℃. If the water temperature is too low, it will cause incomplete combustion of the generator and increase the load of the machine itself. It is recommended to use "soft water" (such as distilled water and rain water) without minerals for cooling water, instead of abusing sewage and muddy water.

發電機維護

Generator maintenance

四、不要超負荷作業

4、 Do not overload

小馬拉大車式的超負荷運行，使相當一部分發電機變?yōu)楹跓?，沒有發揮出應有效能，油耗增大，還會(huì )縮短有關零部件的使用壽命。

The overload operation of the small horse pulling cart has turned quite a number of generators into black smoke, which has not played its due role, increased fuel consumption and shortened the service life of relevant parts.

五、定期檢查

5、 Regular inspection

要注意認真發電機維護和維護，要做到定期檢查調整氣門間隙、噴油壓力、供油時間等，并及時消除冷卻水套的水垢、污物。

Attention shall be paid to the maintenance of the generator. The valve clearance, oil injection pressure, oil supply time, etc. shall be checked and adjusted regularly, and the scale and dirt of the cooling water jacket shall be removed in time.

某些機件如氣門、噴油嘴等，要該修的修，該換的換，重要零部件應一直處于良好使用狀態，避免緊急情況下束手無策、無能為力的情況發生。關注我們http://m.elmasticar.com，了解更多相關事項！

Some parts, such as valves and fuel injection nozzles, need to be repaired or replaced. Important parts should always be in good use to avoid being helpless in an emergency. Follow us http://m.elmasticar.com , learn more about it!